Genesis GMSDB1512L Use and Care Manual download pdf (Page 5)

English

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double insulated tools can use

either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a

heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage,

resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required

minimum wire size.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-gauge cord

can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total

length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for

more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be sure it is marked with the sufﬁx “W-A” (“W” in Canada) to

indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged

extension cord or have it repaired by a qualiﬁed person before using it.

• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

SPECIFIC SAFETY RULES FOR MITER SAWS

WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT (GAINED

FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY RULES. If

you use this tool unsafely or incorrectly, you can suffer serious personal injury!

• Do not operate this miter saw until it is assembled and installed according to the instructions.

• If you are not thoroughly familiar with the operation of miter saws, seek

guidance from your supervisor, instructor, or other qualiﬁed person.

• Mount the tool securely to a stable supporting surface prior to operation.

Ideally, ﬁrmly clamp or bolt your miter saw to a workbench, table, or tool stand at approximately hip height.

• Use the guards whenever possible. Check that the guards are correctly positioned, secured,

and working properly.

• Use only crosscut saw blades. Use only zero-degree or negative hook angles when using

carbide tipped blades. IMPORTANT: Do not use thin kerf blades or blades with deep gullets. These can

easily deﬂect and contact the guard or miter saw table.

• Use only blades that are the correct size and type speciﬁed for this tool.

• Be sure to use a sharp blade that runs freely and is free of vibration.

• Inspect blades for cracks or other damage prior to operation. Replace a cracked or

damaged blade immediately.

• Clean the blade and blade ﬂange washers prior to operation. Again, check for any

damage and tighten the arbor nut securely.

• Use only the blade ﬂanges speciﬁed for this tool.

• Keep your hands out of the path of the saw blade. If the work piece being cut causes

your hands to be within 7-1/4” of the saw blade, the work piece should be clamped in place before making

the cut.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate

Amperes

(At Full Load)

Extension Cord Length

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet

0–2.0 18 18 18 18 16 16

2.1–3.4 18 18 18 16 14 14

3.5–5.0 18 18 16 14 12 12

5.1–7.0 18 16 14 12 12 10

7.1–12.0 18 14 12 10 8 8

12.1–16.0 14 12 10 10 8 6

16.1–20.0 12 10 8 8 6 6

1 2 3 4 5 6 7 8 9 10 ... 71 72

Comments to this Manuals

No comments

Genesis GMSDB1512L Use and Care Manual Page 5

Comments to this Manuals